quality
Rotary Table 4 Inch/100 mm Horizontal Vertical For Milling Premium Quality




Rotary Table 4 100mm Horizontal Vertical Model Milling Machine 4 Slots. The Metal : High quality 18 Gauge Mild Iron steel with Brass Accents. THIS NEAT LITTLE ROTARY TABLE, WITH A DIAMETER OF 100MM, CAN BE USED FOR A VARIETY OF MILLING, DRILLING AND MARKING OUT OPERATIONS IN THE HOME ENGINEER’S WORKSHOP. THERE ARE FOUR TEE SLOTS FOR SECURING THE WORK, FACES MACHINED AT RIGHT ANGLES FOR HORIZONTAL AND VERTICAL MOUNTING AND 7MM SLOTS FOR SECURING TO THE MACHINE TABLE. THE INDEXING HANDLE, WHICH ROTATES ONCE FOR EVERY TEN DEGREES OF TABLE ROTATION, IS SUBDIVIDED IN DEGREES AND QUARTER DEGREES. THE CENTRE HEIGHT WHEN MOUNTED VERTICALLY IS 40MM. SUPPLIED WITH WORK CLAMPING KIT. VERTICAL AND HORIZONTAL MOUNTING TEE SLOTS FOR SECURING WORK WHEEL MARKED IN DEGREES AND QUARTER DEGREES. A Precision work positioning device used in metalworking, enabling the operator to drill or cut work at exact intervals around a fixed axis. Rotary tables are most commonly mounted “flat”, with the table rotating around a vertical axis, in the same plane as the cutter of a vertical milling machine. An alternate setup is to mount the rotary table on its end (or mount it “flat” on a 90° angle plate), so that it rotates about a horizontal axis. In this configuration a tailstock can also be used, thus holding the work piece between centers. Horizontal/Vertical Rotary Tables are extremely useful accessories for a milling machine. Milling curved profiles and angled faces relative to a centre line. Drilling or milling to polar co-ordinates and, when mounted vertically with a tailstock they can be used to machine shafts or spindles. The versatile units can also be used on drilling, boring or slotting machines permitting an even greater range of operations. Machining – To establish the initial work piece position simply loosen the zero Collar locking handle and rotate the zero collar anti-clockwise for about half A turn. The worm is now disconnected from the worm wheel drive, the table is Free to turn independently to the crank handle and the work piece may now be Accurately aligned. To re-engage simply turn the zero collar in the clockwise Direction and re-tighten the locking handle. To machine spanner flats on a bolt. To drill equidistant holes on a circular flange. To cut a round piece with a protruding tang. To create large-diameter holes, via milling in a circular tool path, on small milling machines that don’t have the power to drive large twist drills (>0.500/>13 mm). To cut complex curves (with proper setup). To cut straight lines at any angle. The holiday season is the busiest shopping period of the year, don? Our catalog covers every festival including Thanksgiving, Black Friday, Cyber Monday, Christmas. Please do visit our store and get yourself a treat.

Milling Indexing 4/100 Rotary Table Quality Precision Horizontal Vertical Wi







Tool Set of 4 Regular Rotary Table with a 70 mm 4 Jaws Independent Chuck with Back Plate & fixingsT nut Bolts & M6 clamp kit Chuck Body is Grain SG Caste Iron & Jaws are of Tool Steel. Jaws are Hardened & Ground. A Tool Steel Back Plate is supplied with Fixing T nuts to Mount the Chuck on It. Back Plate is Drill in a manner that it will fit both 3 as well as 4 slots Table. The Back side of the Plate has a locating Spigot to center the Mounting on to the Table. Worm Gear Ratio -1:36, which means that the 1 handle rotation shall turn the table by 10 Degrees. It can be mounted both in Horizontal & vertical position. Hand wheel is graduated in divisions of 10 min & can be set to zero Tool Set of 4 Regular Rotary Table with a 70 mm 4 Jaws Independent Chuck with Back Plate & fixingsT nut Bolts & M6 clamp kit Chuck Body is High Grain SG Caste Iron & Jaws are of Tool Steel. Hand wheel is graduated in divisions of 10 min & can be set to zero.

Milling Indexing 4/ 100 Mm Rotary Table Quality Precision Horizontal Vertical W





Set Of Quality 4 Inches/ 100 MM Regular Rotary Table With Suitable M6 Clamp Kit & 80 Mm Round Vises/ Vices. Table Diameter Is 4 / 100 MM & Is Graduated 360 Degrees. Worm: Gear Ratio Is 1: 36, Which Means 1 Handle Rotation Turns The Table By 10 Degrees. Center Height In Vertical Position 2-1/16/ 50 MM (Only The Table). It Can Be Mounted Horizontally And Vertically. Supplied With A Clamp Kit & Quality Caste Iron 80 Mm Diameter Round Vice With Clamping T Nuts. The Moving Jaw Has Vertical & Horizontal V Grooves To Hold A Round Job. Description of 4 (100 mm) rotary table designed for smaller milling machines. Table diameter 100 mm table is graduated 360 degrees. Worm gear ratio -1:36, which means that the 1 handle rotation shall turn the table by 10 degrees. Center height in vertical position: 2-1/16 (50 mm approx). Hand wheel is graduated in divisions of 10 min & can be set to zero. Can be mounted both in horizontal & vertical position. Details of round vice: details of round vice: 80 mm round vice – made of high grade close grain caste iron. Designed to fit our 3″ (75 mm) & 4″ (100 mm) rotary tables. The moving jaw has v-grooves to hold round objects. Again these vices are drilled in a manner that these can fit to a 3 as well 4 slot table. The drills are counter bored to ensure that the fixing screws sets perfectly ensure perfect movement. Diameter of base : 80 mm jaw width : 54 mm jaw depth: 20 mm jaw opening : 32 mm height : 29 mm.

Milling Indexing 4/100 Rotary Table Quality Precision Horizontal Vertical (usa)






MILLING INDEXING 4/100 ROTARY TABLE QUALITY PRECISION HORIZONTAL VERTICAL WITH SUITABLE M6 CLAMP KIT & SMALL CHUCK (USA). Tool Set of 4 Regular Rotary Table with a 70 mm 4 Jaws Independent Chuck with Back Plate & fixingsT nut Bolts & M6 clamp kit. Chuck Body is High Grain SG Caste Iron & Jaws are of Tool Steel. Jaws are Hardened & Ground. A Tool Steel Back Plate is supplied with Fixing T nuts to Mount the Chuck on It. Back Plate is Drill in a manner that it will fit both 3 as well as 4 slots Table. The Back side of the Plate has a locating Spigot to center the Mounting on to the Table. Worm Gear Ratio -1:36, which means that the 1 handle rotation shall turn the table by 10 Degrees. It can be mounted both in Horizontal & vertical position. Hand wheel is graduated in divisions of 10 min & can be set to zero.

TSL Series High Quality New Condition Vertical Horizontal Rotary Table










This TSL Series High Quality Vertical Horizontal Rotary Table is a must-have for any workshop or manufacturing facility. With its durable construction and reliable performance, it is sure to meet all your needs. The unit is designed for use in both horizontal and vertical settings, making it a versatile addition to your equipment. Crafted by HT-Tools, a trusted brand in the industry, this unit is made in China and comes with a unit quantity of 1. It is perfect for those in need of a reliable and efficient rotary table for their work. Its settings include both horizontal and vertical positions, allowing for maximum versatility in use.

Factory Rotary Table 4 Horizontal & vertical for Milling Machines Quality Made



Please confirm us so that we dispatch your article thanks. Track Page Views With.

Factory Rotary Table 4 Horizontal & vertical for Milling Machines Quality Made



Please confirm us so that we dispatch your article thanks. Track Page Views With.

Milling Indexing 4/ 100 Rotary Table Quality Precision Horizontal Vertical With






Description Of 4 (100 Mm) Rotary Table Designed For Smaller Milling Machines. Table Diameter 100 Mm Table Is Graduated 360 Degrees. Worm Gear Ratio -1:36, Which Means That The 1 Handle Rotation Shall Turn The Table By 10 Degrees. Center Height In Vertical Position: 2-1/16 (50 Mm Approx) Excluding Chuck. Hand Wheel Is Graduated In Divisions Of 10 Min & Can Be Set To Zero. Can Be Mounted Both In Horizontal & Vertical Position. Description Of Chuck Made From Chuck, The Body Of Which Is Made From Sg Iron & Jaws Are Of Tool Steel Hardened & Ground. Supplied With A Mounting Back Plate & Fixing Tee Nuts With Screws. The Back Plate Has Been Drilled In A Manner That It Will Fit To A 3 Slot Or A 4 Slot Rotary Table. A Tool Steel Back Plate Is Supplied With Fixing T Nuts To Mount The Chuck On It. Back Plate Is Drill In A Manner That It Will Fit Both 3 As Well As 4 Slots Table. The Back Side Of The Plate Has A Locating Spigot To Center The Mounting On To The Table. A Suitable M6 Clamp Kit Is Included Along. Tool Set of 4 Regular Rotary Table with a 65 mm 3 jaws Self Centering Chuck with Back Plate & fixings T nut Bolts & M6 clamp kit Chuck Body is Grain SG Caste Iron & Jaws are of Tool Steel. Jaws are Hardened & Ground. Worm Gear Ratio -1:36, which means that the 1 handle rotation shall turn the table by 10 Degrees. A Tool Steel Back Plate is supplied with Fixing T nuts to Mount the Chuck on It. Back Plate is Drill in a manner that it will fit both 3 as well as 4 slots Table. The Back side of the Plate has a locating Spigot to center the Mounting on to the Table. It can be mounted both in Horizontal & vertical position. Hand wheel is graduated in divisions of 10 min & can be set to zero.

4 Inch (100 mm) Quality Regular Rotary Table for Milling indexing table Mach



Brand New 4 Inch (100 mm) Quality Regular Rotary Table for Milling indexing table Machines (U). Brand New Very High Quality 4 /100 mm Regular Rotary Table designed for smaller milling machines. Table is graduated 360 Degrees. Worm Gear Ratio -1:36, which means that the 1 handle rotation shall turn the table by 10 Degrees. Center Height in vertical position: 2-1/16 (50 mm approx) Hand wheel is graduated in divisions of 10 min & can be set to zero. Can be mounted both in Horizontal & vertical position. Meterial – graded caste iron body, alloy steel handle and worm, gun metal gear. Description: 4 Inches (100 mm) Rotary Table Designed for smaller milling machines. Table diameter 100 mm Table is graduated 360 Degrees. All our products are brand new and sealed. We take our reputation seriously.
