Rotary Table for Lathe Milling Indexing Cutting Rotary
(2-3/4 Rotary Table for Watchmaker). Smallest mini Rotary Table for Milling operation with Table Diameter – 2.75 Inches (72 mm). Height when lay Horizontal :1.5 Inches (39 mm). Worm- Gear Ratio is 1: 48, which means that 1 handle rotation shall turn the table 7.5 degrees. Most preferred choice of Watch makers, Jewelry Tools, Model Makers & Hobbyists. 3 Inch (75 mm)Tilting Rotary Table. Low Profile Precision Mini Rotary Table 3 75mm is manufactured from Seasoned casting. Worm- Gear Ratio – 36:1, which basically means that the 1 rotation of the handle shall rotate the table by 10 degrees. Can be used both in horizontal & vertical position. 4 Inch (100 mm)Tilting Rotary Table. Brand New High Quality 4 /100 mm Precision Tilting Rotary Table Features to tilts between 0- 90 Degrees & can be locked at any position. Worm Gear Ratio -1:36, which means that the 1 handle rotation shall turn the table by 10 Degrees. Center Height in vertical position: 2-5/8 (66 mm approx). Hand wheel is graduated in divisions of 10 min & can be set to zero. (3 inch 75mm Rotary Table). Table diameter 80 mm (3) Table is graduated 360 Degrees. Center Height in vertical position without chuck: 2-5/8 (66 mm approx). Can be mounted both in Horizontal & vertical position. 4 Inch (100 mm) Rotary Table. Brand New Very High Quality 4 /100 mm Regular Rotary Table designed for smaller milling machines. Table is graduated 360 Degrees. Center Height in vertical position: 2-1/16 (50 mm approx). (HV6 Rotary Table 6 /150MM – 4 Slot). Manufactured from High grade seasoned casting and powder coated wrinkled finish for smooth looks. Precision ground chuck and overall smooth surface. Gear Ratio 90:1 Center Bore MT-2 T Slot 16mm Horizontal Height : Approx 80mm from Base to Top surface of Chuck Satin Chrome Dials. This will fit both the Horizontal & Tilting model of HV4 & HV6 Rotary Tables. This Set includes Following: 2 x step blocks 2 x tee bolts. With flanged nut 2 x clamps Bolt Thread M8. HV4(110 MM) 3 slot Rotary Table. Table Diameter is 110 mm with MT2 Bore. Table Height when laid Horizontally 80 mm Worm -Gear Ratio is 1: 90, which means 1 handle rotation turns the Table by 4 Degrees. 4-Jaws x 6″/ 150 mm Wood Lathe Chuck Threaded 3/4″ x 16 with Independently Adjustable / Reversible Jaws. Handwheel graduated in seconds. 2 Oiling Points for a direct lubrication of the Table for longer life & better performance. Can be clamped in Horizontal as well Vertical Position. Vernier scale calibrated to 10 seconds quick release system for manual indexing. HV6 3-Slot Rotary Table (150 mm -6 Inches). Graduated 360 degree around its circumference. (New 3” 80mm Tilting Rotary Table). Low Profile Precision Mini Rotary Table 3 /80 mm is manufactured from Seasoned casting. Worm- Gear Ratio – 36:1, which means that the 1 rotation of the handle shall rotate the table by 10 degrees. Designed to tilt between 0- 90 Degrees & can be locked at any position. Zero dial is marked in 10 minutes divisions. Table scale is calibrated in 5 degree increments. Height when laid horizontally 60 mm. Grub screw on the base plate for dialing the Rotary accurately when laid horizontal.