Milling Machine Rotary Table
Watchmaker 2.75 Inch. Smallest mini Rotary Table for Milling operation with Table Diameter – 2.75 Inches (72 mm). Height when lay Horizontal :1.5 Inches (39 mm). Worm- Gear Ratio is 1: 48, which means that 1 handle rotation shall turn the table 7.5 degrees. Most preferred choice of Watch makers, Jewelry Tools, Model Makers & Hobbyists. 3 Regular 3 Slots (80 mm). Quality Low Profile Small Rotary Table diameter 80 mm (3Inches), Table is graduated 360 Degrees. Worm Gear Ratio -1:36, which means that the 1 handle rotation shall turn the table by 10 Degrees. Horizontal Center Height when lay flat : 44 mm. Center Height in vertical position is 45 mm approx. Can be mounted both in Horizontal & vertical position. Hand wheel is graduated in divisions of 10 min & can be set to zero. Base Dimensions: 110 x 85 mm II 2 x U slots for clamping: 8 mm. It is mainly used to cut gear teeth accurately and equal spacing of the teeth of the gear. Also used for milling gears, splines, squares, cutting of flutes in reamers, drills and milling cutters, racks, grinders, etc. We also offer various accessories like Chucks, Back plates, Clamp kits, Collet Adaptors and Tailstock to suit these rotary table functioning. Pls check our other listings if you need anything from this category. 3 Regular 4 Slots (80 mm). Made out of high grain casting, this precision quality low profile rotary table diameter is 80 mm (3Inches) and is most popular light weight rotary table for small and light duty milling operations. Table is graduated 360 Degrees. Total Height when laid flat is 1-3/4 (44 mm). Center Height in vertical position: 1-3/4 (45 mm approx). Can be clamped both Horizontally and Vertically. Base Dimensions : 110 x 85 mm with 2 x U slots (7.5 mm wide) each wall for Horizontal and Vertical clamping purpose. 3 Tilting 4 Slots (80 mm). Made out of high grain casting, this precision quality low profile rotary table diameter is 80 mm (3Inches) and is most popular light weight tilting rotary table for small and light duty milling operations. Can be clamped vertically and horizontally both ways. Designed to tilt between 0- 90 Degrees & can be locked at any working angle position. Total Height when laid flat is 2-7/16 (62 mm). Center Height in vertical position: 2-17/32 (61.5 mm approx). Base Dimensions : 100 x 105 mm with 2 x Drills (8 mm diameter) at a PCD of 82 mm approx. Weight of the Rotary Table : 2.700 Kgs. 3/80 mm Regular, with M6 Clamp Kit. Supplied with a suitable M6 Clamp kit along with this rotary table. Clamp kit is hardened and precisely ground before being epoxy black finish for a rust free life. 3/80 mm Tilting, with M6 Clamp Kit. Supplied with a suitable M6 clamp kit which is hardened and ground before the epoxy black finish for a rust free life. 3/80 mm Regular, ER16 Collet Adaptor with M6 Clamp Kit. Supplied with an ER16 Collet Adaptor with fixing T nuts bolts. The assembly height with ER16 collet clamped on the table is approx 80 mm. 3/80 mm Tilting, ER16 Collet Adaptor with M6 Clamp Kit. Total Height when laid flat is 2-7/16 (62 mm) without collet adaptor. The assembly height measures to be 98 mm (with ER16) adapter mounted on it. Supplied with 1 Pc each of ER16 collet adaptor Pc, suitable M6 clamp kit which is hardened and ground before the epoxy black finish for a rust free life. Supplied with 1 Pc each of ER16 collet adaptor along with a M6 clamp kit which is hardened and ground before the epoxy black finish for a rust free life. 3/80 mm Regular, ER16 & 20 Collet Adaptor with M6 Clamp Kit. Total height of the assembly with a ER16 collet adaptor is 80 mm, and 82 mm when clamped with a ER20 adaptor. Also Supplied with a suitable M6 Clamp kit along with this rotary table. 3/80 mm Tilting, ER16 & 20 Collet Adaptor with M6 Clamp Kit. The assembly height measures to be 98 mm (with ER16) and 101 mm approx (with ER20) collet adapter mounted on it. Supplied with 1 Pc each of ER16 and ER20 collet adaptor Pc each of ER16suitable M6 clamp kit which is hardened and ground before the epoxy black finish for a rust free life. Supplied with 1 Pc each of ER16 and ER20 collet adaptor along with a M6 clamp kit which is hardened and ground before the epoxy black finish for a rust free life. 3/80 mm Regular, ER 20 Collet Adaptor with M6 Clamp Kit. Supplied with an ER20 Collet Adaptor with fixing T nuts bolts. The assembly height with ER20 collet clamped on the table is approx 82 mm. 3/80 mm Tilting, ER 20 Collet Adaptor with M6 Clamp Kit. The assembly height measures to be 101 mm approx (with ER20) collet adapter mounted on it. Supplied with 1 Pc each of ER20 collet adaptor, suitable M6 clamp kit which is hardened and ground before the epoxy black finish for a rust free life. Supplied with 1 Pc of ER20 collet adaptor along with a M6 clamp kit which is hardened and ground before the epoxy black finish for a rust free life. 4 Regular 3 Slots (100 mm). Made of Caste Iron, Precision High Quality 4 /100 mm Regular Rotary Table designed for smaller milling machines. Height when laid horizontally 2-5/16 Inches (58 mm). Center Height in vertical position: 2-1/8 (53.5 mm approx). Base Dimensions : 135 mm x 105 mm with 2 x U slots (9.5 mm). Body is painted and Rest all working surfaces are precision ground. The Dial and locking screws are plated and Handle has epoxy black finish for a rust free life. Smooth Jerk free easy rotation with negligible play. The top of the table is ground to eliminate any excess run out. 4 Regular 4 Slots (100 mm). 4 Tilting 4 Slots (100 mm). Brand New High Quality 4 /100 mm Precision Tilting Rotary Table Features to tilts between 0- 90 Degrees & can be locked at any working position. Provided with oil nipple for oiling of inside body. Center Height in horizontal position when lay flat : 2-3/4 (70 mm approx). Center Height in vertical position: 3 Inch approx (77 mm). Body & table are made of caste Iron. Rest of the parts are made of tool steel. Body is painted black. Knobs, dials and locking screws are all plated and Rest of the working surface are precisely ground. Rotary’s handle are knurled for firm gripping while rotating and epoxy black finish for a long rust free life. Base Dimensions : 142 x 128 mm. 2 Opposite counter drills of 9.5 mm diameter are located at a PCD of 102 mm approx for mounting. 4/100 mm Regular with M6 Clamp Kit. Supplied with a suitable M6 clamp kit which is hardened and ground before being epoxy blacked to avoid any rust on it with time. 4/100 mm Tilting, with M6 Clamp Kit. Supplied with a suitable M6 clamp kit which is hardened and precisely ground before the epoxy black finish for a rust free life. 4/100 mm Regular, ER16 Adaptor with M6 Clamp Kit. Height when laid horizontally 2-5/16 Inches (58 mm) without the Adapter & 105 cm (with ER16) collet adapter mounted on it. Supplied with 1 Pc each of ER16 collet adaptor with fixing t nuts/ bolts along with a suitable M6 Clamp kit, which is hardened and black for rust free life. 4/100 mm Tilting, ER16 Collet Adaptor with M6 Clamp Kit. Center Height in horizontal position when lay flat : 2-3/4 (70 mm approx) without the Adapter & 105 cm (with ER16) collet adapter mounted on it. This package include an ER16 collet adapter with fixing t nuts and bolts along with a M6 clamp kit having epoxy black finish for a rust free life. The clamp kits are also hardened and precisely ground before that. 4/100 mm Regular, ER16 & 20 Collet Adaptor with M6 Clamp Kit. Height when laid horizontally 2-5/16 Inches (58 mm) without the Adapter & 105 cm (with ER16) and 108 mm (with ER20) collet adapter mounted on it. Supplied with 1 Pc each of ER16 and ER20 collet adaptor with fixing t nuts/ bolts along with a suitable M6 Clamp kit, which is hardened and black for rust free life. 4/100 mm Tilting, ER16 & 20 Collet Adaptor with M6 Clamp Kit. Center Height in horizontal position when lay flat : 2-3/4 (70 mm approx) without the Adapter & 105 cm (with ER16 & ER20) collet adapter mounted on it. This package include an ER16, a ER20 collet adapter with fixing t nuts and bolts along with a M6 clamp kit having epoxy black finish for a rust free life. 4/100 mm Regular, ER 20 Collet Adaptor with M6 Clamp Kit. Height when laid horizontally 2-5/16 Inches (58 mm) without the Adapter & 108 mm (with ER20) collet adapter mounted on it. Supplied with 1 Pc each of ER20 collet adaptor with fixing t nuts/ bolts along with a suitable M6 Clamp kit, which is hardened and black for rust free life. 4/100 mm Tilting, ER20 Collet Adaptor with M6 Clamp Kit. Center Height in horizontal position when lay flat : 2-3/4 (70 mm approx) without the Adapter & 105 cm (with ER20) collet adapter mounted on it. This package include an ER20 collet adapter with fixing t nuts and bolts along with a M6 clamp kit having epoxy black finish for a rust free life. HV6-3 Slots (6-150 mm) Tilting. Quality precision 6 Inch /150 mm table diameter HV6 Tilting Horizontal & Vertical Rotary Table, calibrated to tilt and set at any working angle between 0-90° degrees. Dis-engage-able hand wheel for free table rotation. Lubrication points to worm and table rotation. Micro collar graduated in steps of 1 min. One rotation of the hand-wheel rotates the table 4 degrees. Height horizontal: 132 mm. Centre height in vertical position : 112 mm Centre bore : 2MT Worm gear ratio : 1:90. Remarkable Quality: Cast iron mainly used to cast parts subjected to pressure and vibration on mechanical equipment, offering rotary table for milling durability, shock absorption and heat-resistance. Multiple Application: These sturdy heavy milling tables are widely used in milling machine like index boring, milling, circle cutting, spot facing and boring hole and so on. Practical design can meet a variety of workshop work needs. HV6 (6 Inch -150 mm) 3 Slots. Manufactured from High grade seasoned casting and powder coated wrinkled finish for smooth looks. Precision ground chuck and overall smooth surface. Gear Ratio 90:1, which mean 1 handle rotation will move the table by 4 Degrees. T Slot 16 mm. Table is graduated 360 degree around its circumference. Horizontal Height : Approx 80mm from Base to Top surface of Chuck. Centre Height in Vertical Position: 105 mm. Table Graduated 360 Degrees, Resettable Dial & Handwheel graduated in seconds. Vernier scale is caliberated to 10 seconds. 2 Oiling Points for a direct lubrication of the Table for longer life & better performance. We offer compatible dividing plates, tailstock, chucks and clamp kit sets as well for this Rotary table. If you need one, pls check out our store to check them out. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Workholding & Toolholding\Workholding\Rotary Tables”. The seller is “tools-shop2020″ and is located in this country: IN. This item can be shipped worldwide.
- Operation: Manual
- Setting Position: Horizontal/Vertical
- SIZE: 3\
- Brand: Unbranded